New water supply piping during a repipe

Low Water Pressure in Arvada: 7 Common Causes

Short answer: If only one faucet is weak, it’s usually a clogged aerator or cartridge. If the whole house is weak, check that the main valve is fully open, then look at the pressure regulator, hidden leaks or old galvanized pipe.

New water supply piping during a repipe – Low Water Pressure in Arvada: 7 Common Causes
#CauseClueFix
1Clogged aerator or shower headOne fixture onlyClean with vinegar
2Worn cartridgeOne faucet, hot or coldReplace cartridge
3Main valve partly closedAfter recent workOpen fully
4Failing pressure regulatorWhole house, sudden changeReplace regulator
5Hidden leakMeter moving with water offLeak detection
6Galvanized pipe corrosionOlder home, getting worse over yearsRepiping
7Provider issueNeighbors affected tooContact your water provider

Quick checks

  1. Test several faucets, hot and cold.
  2. Ask a neighbor if their pressure is normal.
  3. Check the main valve is fully open.
  4. Do the meter test for leaks.

Still weak? Call to discuss your plumbing problem.

Hot side only?

If only hot water is weak, the problem is usually the water heater: sediment in the tank, a partly closed valve on top of the heater, or scale in the outlet. Flushing the heater often helps. See water heater noise for sediment signs.

Pressure regulator basics

Many homes have a pressure reducing valve (PRV) where the main line enters. These wear out over time. A failing PRV can cause low pressure, or the opposite: pressure that is too high and stresses fixtures. A plumber can test your pressure with a gauge on a hose bib.

Pressure readingWhat it means
Below 40 psiLow. Check regulator, valves, pipes
40 – 80 psiNormal range for most homes
Above 80 psiHigh. Regulator may need adjustment or replacement

How to check your water pressure

A pressure gauge that screws onto a hose bib is easy to find at any hardware store and gives you a real number instead of a guess.

  1. Turn off every faucet, appliance and sprinkler in the house.
  2. Screw the gauge onto an outdoor hose bib or the washing machine connection, as close to the main as you can.
  3. Open the valve fully and read the gauge.
  4. Check again in the morning and evening. Pressure that swings a lot can point to a failing regulator.

The meter test for hidden leaks

  1. Turn off all water use inside and outside the home.
  2. Find your water meter and note the reading, or watch the small leak indicator.
  3. Wait 15 to 30 minutes without using any water.
  4. If the reading changed or the indicator moved, water is leaking somewhere. See leak detection.

Pipe type and pressure

Pipe typeEffect on pressureWhat to do
Galvanized steelRusts and narrows inside, so pressure drops slowly over the yearsRepiping is the lasting fix
CopperUsually good flow; scale can build up with hard waterClean aerators, check the regulator
PEXGood flow; undersized lines can feel weak when two fixtures runCheck line size and the regulator
Polybutylene (gray plastic)Can leak at fittings, which lowers pressureHave it inspected; replacement is often advised

When to call a plumber

  • Low pressure throughout the house that you cannot explain
  • Pressure dropped suddenly
  • Water bill rose at the same time (possible leak)
  • Old galvanized pipes in the home

Related pages

Frequently asked questions

Can a water softener lower pressure?

A clogged or undersized softener can. Try its bypass valve to see if pressure improves.

Is low pressure a sign of a leak?

It can be, especially if your water bill also went up.

What is normal water pressure for a house?

Most homes run between 40 and 80 psi. Around 50 to 70 psi feels comfortable without stressing pipes and fixtures.

Why is my pressure low in only one shower?

It is usually the shower head or the valve cartridge. Clean the head in vinegar first, then replace the cartridge if flow is still weak.

Can I adjust my pressure regulator myself?

Many regulators have an adjustment screw, but a regulator that is old or failing will not hold a setting. If pressure keeps drifting, it is time to replace it.

Low pressure by situation

SituationMost likely cause
After plumbing workValve not fully opened or debris in aerators
Only upstairsPipe size or regulator setting
Getting worse over yearsCorroding galvanized pipe or scale
Sudden drop everywhereRegulator failure, leak or provider issue
During heavy use onlyUndersized lines or regulator

Simple fixes to try first

  1. Unscrew and clean faucet aerators and shower heads.
  2. Make sure the main valve is fully open.
  3. Check the softener or filter bypass to see if pressure improves.
  4. Ask neighbors if their pressure is also low.

Arvada factors

Older homes in south and east Arvada are more likely to have galvanized pipe, which narrows over time. Hard water can also build scale in fixtures. See Arvada hard water and repiping.

Key takeaways

  • One weak faucet is usually a clogged aerator or cartridge.
  • Whole-house low pressure can be a regulator, a leak or old galvanized pipe.
  • Normal home pressure is roughly 40 to 80 psi.
  • A sudden drop plus a higher water bill can point to a leak.

If you have tried the simple fixes and pressure is still low, a plumber can test your pressure, check the regulator and look for leaks in one visit.

Water where it should not be? Call now.

Talk with a local Arvada plumbing pro about your problem and your options.

Similar Posts